IEPE Sensor Supply - IEPE Power Supply - IEPE Sensor Amplifier
IEPE compatible transducers. It has two channels input/output with BNC connector, and wide voltage power supply supports the use of various DC power supplies.
ICCP is a well-established standard which is widely used in the acoustic and vibration field to convert the high impedance signal of measurement microphones and piezoelectric transducers to a low impedance voltage output signal.
The abbreviation ICCP stands for “Integrated Constant Current Power” and has many manufacturer specific names such as ICP® (Integrated Circuit Piezoelectric), CCLD, DeltaTron®, ISOTRON® and IEPE (Integrate Electronics Piezoelectric)
8201T
- Price: 240 €
1 Channel IEPE Sensor Supply
8201T is a portable single channel IEPE sensor signal conditioner.
It provides a 24 V / 4 mA power supply for sensors with integrated amplifiers.
The frequency response goes from 0.3 Hz to 100 kHz, so this is perfectly adequate for most IEPE sensors.
The 8201T is equipped with a high-quality, sturdy aluminum housing.
1-channel IEPE supply
24V/4mA
Output voltage max.: 10 Volt eff
Frequency response: 0.3 Hz 100 kHz.
8201
1-channel IEPE supply
24V/4mA
0, +20 dB
Output voltage max.: 10 Volt eff
Frequency response: 0.3 Hz 100 kHz.
- Price: 368 €
1 Channel IEPE Sensor Amplifier
8201 is a portable single channel IEPE sensor signal conditioner.
It provides a 24 V / 4 mA power supply for sensors with integrated amplifiers.
Two selectable gains 0dB and + 20dB are available.
Signal conditioning indicators minimize the risk of operator error.
The integrated rechargeable 9 volt battery is designed for a long operating time of more than 5 hours.
Recharging can be done during operation.
The frequency response goes from 0.3 Hz to 100 kHz, so this is perfectly adequate for most IEPE sensors.
The 8201 is equipped with a high-quality, sturdy aluminum housing.
MC102A
MC102A has an all-aluminum housing, which can effectively shield the internal signal.
The LED indicators display the power supply status and the input status of each channel (input open (sensor not connected), OK (sensor connected), and input shorted).
Each channel has a 35Vp input and output protection circuit, which can protect sensors and data acquisition equipment.
- MC102A Datasheet
- Price: 420 €
2 Channel ICCP Power Supply
MC102A power supply can provide power for prepolarized microphones, accelerometers and other ICCP compatible transducers. It has two channels input/output with BNC connector, and wide voltage power supply supports the use of various DC power supplies.
ICCP is a well-established standard which is widely used in the acoustic and vibration field to convert the high impedance signal of measurement microphones and piezoelectric transducers to a low impedance voltage output signal.
The abbreviation ICCP stands for “Integrated Constant Current Power” and has many manufacturer specific names such as ICP® (Integrated Circuit Piezoelectric), CCLD, DeltaTron®, ISOTRON® and IEPE (Integrate Electronics Piezoelectric).
MC102A is compatible with microphones or transducers using any of the above proprietary names.
Provides power for microphones, accelerometers and other ICCP transducers
2 channel input/output with BNC connector
LED indicators show the status of each input channel
4 mA/24 V ICCP power supply
7 V~30 V wide voltage DC power supply
Frequency Response 0.4 Hz ~ 200 kHz (±3 dB)
8204
- Price: 1960 €
4 Channels IEPE Conditioner
8204 4 channels IEPE sensor signal conditioner
Selectable current (4 or 10 mA); Selectable gain 1 to 100
Two types of output connector; Wide frequency range
For monitoring normal or faulty circuit condition by status LEDs
Wide frequency response, Low noise, Good stability
Gain, Excitation current switchable
Apply for IEPE Transducer’s general test
4 channels IEPE supply
Excitation Voltage 24 Volt
Gain 1, 10, 100
Excitation Current: OFF, 4 mA, 10 mA, 20 mA
Output voltage max.: 10 Volt eff
Frequency response: 0.3 Hz 100 kHz.
Input/output Type: BNC/BNC
Size mm : 45×122×200
Weight : 1.4 kg
Power Supply:220V50Hz | 0.2A
®TRADEMARK
ICP is a registered trademark of PCB Piezotronics, Inc., DeltaTron is a registered trademark of Hottinger Brüel & Kjær A/S, ISOTRON is a registered trademark of ENDEVCO.
This document only describes the technical principles involved and inevitably mentions the registered trademarks of other manufacturers, which is not intended and will not harm the interests of trademark owners. The registered trademarks mentioned above belong to their respective owners.